Items:
0
Total:
$0
View Cart

Shopping Cart

0 item(s) in your shopping cart

ITEMS
QTY
PRICE
Total
 
[ITEM_NAME]
View/Hide options
This item will Autoship every [recurring_frequency]
[ITEM_PRICE]
[ITEM_SUBTOTAL]
Subtotal: $0
Your cart is empty.

Banded Turquoise Urban Raku Bracelet

Banded Turquoise Urban Raku Bracelet

Want to make this Design Idea? See products and other information below.

Supply List:

  • 1 Urban Raku Bracelet Cuff Rectangle - Turquoise Copper
  • 7 inches Leather Flat 20mm - Brown
  • 7 inches Leather Flat 5mm - Teal
  • 6 TierraCast Snap Rivets 4mm - Silver Plate
  • 1 Leather Clasp Magnetic Plain 20mm - Antique Silver OR 1 Leather Clasp 20mm Rivets - Antique Silver
  • 2 12mm Rubber O-Ring Spacer - Chocolate
  • Super New Glue

    Finished Length: 7 1/2 inches

    Level of Difficulty: Intermediate

    Tools: Leather Punch, Nail Setter, 4mm rivet setter, Bench Block, Hammer, Pen, Ruler, Leather Cutter or Sharp Scissors
  • Designer Tip: SEE VIDEOS LINKS BELOW. Thread the 5mm leather through the holes of the bracelet cuff as shown. Mark 2 holes about inch from the focal holes and punch a hole using the nail setter. Center the 5mm leather on the 20mm leather and mark/punch 2 corresponding holes in the 20mm leather using the 5/64 inch setting on the leather punch. Use 2 4mm snap rivets to attach the 5mm leather to the 20mm leather with the 4mm rivet setter. Punch 2 additional holes in both the 5mm and 20mm leather on either side of the focal as described above and set 4mm rivets in each set of holes. Add an O-Ring to each end of the bracelet. Check the size and trim the 20 mm leather if needed before gluing the leather into the clasp. Close the clasp and trim the 5mm leather flush with the clasp. Slide the O-Ring over the 5mm leather next to the clasp to hold the 5mm leather in place. We also recommend adding a few drops of glue behind the 5mm leather at the clasp to hold it in place. (not shown in the video).

    Helpful Video Tutorial:Click here to Watch How to Rivet a Two Hole Urban Raku Focal and Click here to Watch Basic Gluing and Sizing of Leather Bracelets and Click here to Watch Using Colorful Rubber O-Rings on Regaliz & Euro Leather Cord Tutorial - Beginner

    To add items to your cart, fill in the desired quantity at the top or bottom of the page to add all selected items to your shopping cart.

    Products (Total Items: 3)
    Sort by:
    Select Quantities
    20mm Rivet Flat Leather Cord Magnetic Clasp - Antique Silver
    20mm Rivet Flat Leather Cord Magnetic Clasp - Antique Silver
    Part #: FL-CLM-15AS
    29x23x5mm
    Hole size: 20x2.5mm
    Sold Individually
    PEWTER plated with 99.9% sterling silver
    Use 2 lengths of 10mm FLAT leather or 4 Lengths of 5mm FLAT leather
    OrUse 1 length of 10mm and 2 lengths of 5mm FLAT Leather
    Clasp adds about 1 inch
    Ends must be glued with a super glue designed for leather and metal

    CLICK HERE FOR QTY DISCOUNT
    Your Price: $14.70
    0 In Stock
    Enter
    Quantity
    Average Rating0 Review(s)
    Nail Setter 1/32
    Nail Setter 1/32"
    Part #: NAIL-1
    NAIL-1 - Use this tool to set TierraCast 4mm Snap Rivets on C-Koop Enamel Rivetables and Stackables
    Length: 4 inches Diameter: 1/32 inch
    Sold Individually
    Made out of Stainless Steel
    Your Price: $6.55
    7 In Stock.
    Enter
    Quantity
    Average Rating0 Review(s)
    !Cutter Leather Black
    !Cutter Leather Black
    Part #: RZ-CUTTER
    RZ-CUTTER - Used to cut ALL Leather
    Click here for Replacement Blades - RZ-RBLD
    Sold Individually
    Your Price: $13.25
    0 In Stock
    Enter
    Quantity
    Average Rating3 Review(s)
     
    Select Quantities